Technical Bulletin, New VW ATF / 01M transmission, checking ATF level, changing ATF

Short Description
A new Volkswagen ATF (Automatic Transmission Fluid) is available. Only the new VW ATF must be used in all Volkswagen Phase II automatic transmissions (types 01M and 01P). These transmissions have been installed in production beginning in January 1995. VW ATF is a yellowish-colored fluid unlike the red Dexron II fluid used previously. Use Dexron II transmission fluid only for automatic transmissions in vehicles produced up to and including December 1994. VW ATF can also be used in these transmissions.

Website: www.diakom.ru | Filesize: 110kb
No of Page(s): 6

Content
…
ATF, changing
– Remove ATF level plug from oil pan (arrow).
– Remove overflow tube through the plug hole.
– Drain ATF.
– Install overflow tube.
– Screw level plug in hand-tight.
– Fill with 3 Liters of ATF through filler pipe.
– Start engine and shift through all selector lever positions with vehicle stationary.
…

Get the file Download here

Volkswagen Passat B6 - Wheel bearings, assembly overview

Short Description
Wheel bearings, assembly overview
- Multi-point socket head bolt
- Tip of bolt must point in direction of travel
- Left Front ABS Wheel Speed Sensor G47 / Right Front ABS Wheel Speed Sensor G45
- Can be checked in Guided Fault Finding using Vehicle Diagnosis, Testing and Information System VAS 5051

Website: volkswagen.msk.ru | Filesize: 271kb
No of Page(s): 9

Content
…
- Remove brake disc.
- Remove shield from wheel bearing housing.
- Loosen tie rod end nut, do not remove.
To protect threads, leave nut on stud a few turns.
…
- Press off tie rod end from wheel bearing housing using ball joint puller 3287A , and then remove nut.
- Press drive axle out of hub as far as possible (in direction of transmission).
…

Get the file Download here

Technical Bulletin, Glove Box, Eliminating Squeaks/Rattles

Short Description
Condition
- Glove box door squeaks when opening and closing.
- Glove box rattles when closed while driving.

Website: www.postamatik.com | Filesize: 798kb
No of Page(s): 3

Content
Service
Glove box door, squeaking
– Release cover -1- with clips -2- from dash panel -3-.
– Pull out cover -1- in direction of -arrow-.
– Open glove box door until door damper (brake element) actuator rod for door -arrow– is fully extended.
– Lightly apply silicone spray to brake element actuator rod -arrow-.
– Open and close glove box door 5 to 6 times and ensure noise or squeak has been eliminated during glove box door operation.
…

Get the file Download here

Volvo 2005 Aero Mirror Systm Service Manual

Short Description
Product Features
- Replaceable Components
- Minimal Diagnosis and Repair Time
- Spring-Loaded Fold Away Bracket Feature
- Remote Control Main Mirror
- Self-Regulating Heaters
- Look-Down Mirror on Passenger Side

Website: www.lang-mekra.com | Filesize: 3066kb
No of Page(s): 30

Content
…
Removal of Mirror System
- Remove Antenna from Antenna Base
- Disengage Third Arm from Bracket Receiver
- Loosen (do not remove) 2 Bolts from Upper Holder using a T-40 driver. Be sure to hold the Mirror stady to prevent damage or personal injury.
- Remove the 3 Bolts from the Lower Holder from inside the door hinge, using a T-40 driver.
- Gently pull the Lower Holder away from the door to expose the Control Harnes and CB Cable, disconnect both
- Supporting the weight of the Mirror Systm carefully, remove the 2 loosened Bolts from the Upper Holder. The Mirror Systm is now free.
…

Get the file Download here

SUZUKI LTR450 Fuelpak Installation Instruction

Short Description
To achieve the optimum performance from your application, it is recommended that you install a high performance air filter in conjunction with this unit. Fuelpak will be installed in-line with the factory injector wiring harness and the throttle position sensor. The unit will be mounted under the seat.

Website: www.fuelpakfi.com | Filesize: 216kb
No of Page(s): 2

Content
…
(Important Note): Fuelpak maps for the LTR450 were created with a White Brothers Power Pro performance module installed. The included Power Pro unit must be used in conjunction with the Fuelpak for proper function. Failure to do so will result in poor performance and may cause engine damage.
1. Be sure that key is in the off position, then remove seat.
2. Referring to figure 1, remove (4) push pins and (1) 10mm bolt. Repeat for opposite side. Push pins that are accessible from the back can be popped out by pushing on the pin from the back side. Push pins with flanged pin heads can be gently pried up with a slotted screwdriver.
3. Remove fuel cap and tank cover. Reinstall fuel cap.
4. Clean Fuelpak mounting location with alcohol and allow to dry. Referring to figure 2, mount Fuelpak as shown with supplied Velcro. Route harness as shown, between airbox and subframe, and underneath subframe cross brace.Gently pull up and out on subframe side cover and attach harness to subframe with included zip ties. Ensure that harness is not running over black rubber strip behind airbox.
…

Get the file Download here

Download Auto Manual Fiat Brava Bravo 1995 – 1999 Wiring Diagrams

Download Auto Manual Fiat Brava Bravo 1995 – 1999 Wiring Diagrams. Index to diagram 2 starting and charging, engine cooling fan, horm, heated rear window, interior ventilation 3 front and rear screen wash/wipw, headlight wash, hazard warning lights 4 directions indicator, brake lights, reversing lights 5 exterior lights.

anti-lock braking system 6 fog lights – front and rear, electric windows (front) 7 cigarette lighter, headlight alignment, high level radio 8 interior lighting, sun roof, heated and adjustable rear view mirrors 9 weber IAW ignition and injection system (1.6SX, ELX, HLX) 10 Bosch Mono Motronic ignition and injection system (1.4S, SX, Team, 80). Earth location E1 Battery earth on bodyshell, E2 left front earth E3 left dashboard earth E4 right front earth E5 left rear earth E6 right rear earth E7 right dashboard earth E8 earth for electronic injection E9 earth for electronic ignition. Key to symbols: 20 Item number bulb switch multiple contact switch (ganged) fuse/fusible link, solenoid actuator resistor variable resistor internal connection in a component block connection, detachable wire connection, fixed wire colour (green wire with yellow tracer) interconnection line (thin line) denotes alternative wiring variation connections to other circuits earth point with location code pump/motor dashed outline denotes part of a larger item.

Download Auto Manual Fiat Brava Bravo 1995 – 1999 Wiring Diagrams

Owner Manual Fiat 500

Content:
This is an electrical engine locking system which increases protection from attempted theft of the car. It is automatically activated when the ignition key is extracted. Each time the car is started turning the ignition key to MAR, the Fiat CODE system control unit sends a recognition code to the engine control unit to deactivate the inhibitor. Replacement remote control placement To replace the remote control cover, follow the procedure shown in figure.

Instrument panel and on-board instrument Versions with multifunctional display. The car can be equipped with the multifunctional reconfigurable display that, according to the settings made, will show useful information necessary when driving. Menu function, seats All adjustments must be made with the car stationary. Lift lever A and push the seat forwards and backwards: your arms should rest on the steering wheel rim while you are driving. Driver side and passenger side where position memory is provided. Steering wheel It can be adjusted vertically (where provided).

Wiring Diagram Fiat Spider 2000 Type CSO

Power Windows and radio circuits, Parking License Plate, Side Marker, Panel Light, Hazard and Turn Signal, Backup and Stop Lights Circuits, High and low beam circuits, ignition starter, alternator, engine cooling fan,

power distribution circuit, automatic transmission starter circuit, fuel injection system circuits, instrument indicators, seat belts and remove key warnings, courtesy light, clock and socket circuits.

Wiring Diagram FIAT Spider 124 Type BS

The diagrams in this document are entirely vector-based. This means that they can be scaled to virtually any size and printed from computers that run Adobe Acrobat. The wiring diagram explain location of Front direction Indicators, Front parking lights,Headlamps (high and low beams ).

Motor compress or for electro pneumatic horns, Horn control relay switch, Engine cooling fan motor, Ignition coil, Oil Pressure Gauges ending unit, Ignition Distributor, Engine fan motor thermostatic switch, Insufficient Oil Pressure indicator sending unit, Button switch for electro valve energizing during fast idle rate adjustments.

Online Auto Manual Fiat Brava Bravo 1.4 12V PDF

Online Auto Manual Fiat Brava Bravo 1.4 12V PDF. Fiat Brava BRavo Owners Manual Repair Maintenance sul polo negativo della batteria Scollegare la batteria prima di effettuare qualsiasi operazione Saldare le connessioni elettriche Non utilizzare rubacorrente.

Separate the throttle body and insert the mixer in the middle 4 wires Oxigen sensor Signal is on the black wire Switch LES emulation to Bosch singlepoint position T P S signal is on wire 4 Connect L E S ground to the battery negative pole Disconnect the battery before working Soft solder wiring connections Do not use fast connections OTHER SUGGESTED MATERIAL Pipes and fitting set 54 lt LPG tank tank fixing bracketts for Fiat Tipo NOTES Separer le groupe du monoinjecteur en y installant le melangeur au milieu Sonde lambda 4 fils Signal sur fil noir Positionner le micro switch du L E S sur la position monoinjection Bosch Signal TPS sur fil n 4 Fixer la masse du LES sur le p le negatif de la batterie D connecter la batterie avant d effectuer n importe quelle operation Souder les connections electriques Ne pas utiliser de connections rapides MATERIEL CONSEILLE Kit tuyaux et raccords R servoir G P L lt 54 support pour Fiat Tipo NOTAS Dividir el cuerpo del monoinycettor e instalar el mezclador en el medio Sonda Lambda con 4 cables se al en el cable negro Programar la simulaci n del Les en posici n monoinyector Bosch Se al T P S en el cable n 4 Fijar la masa del LES en el polo negativo de la bateria Desconectar la bater a antes de efectuar cualquier operaci n Soldar las conecciones el ctricas No utilizar conecciones r pidas MATERIAL ADICIONAL ACONSEJADO Set ca er as y racores Tanque G L P lt 54 soporte para Fiat Tipo Landi S r l si riserva di modificare la presente scheda senza alcun preavviso al fine di migliorare il funzionamento della vettura Landi S r l reserves the right to modify this specification sheet without previous notice in order to improve the vehicle performances.

Download Online Auto Manual Fiat Brava Bravo 1.4 12V PDF

Modification and Integration Fuel Gauge Volkswagen Golf TDI

Step by step instructions : Always disconnect the battery before doing any electrical work on the car. Instructions: 1. Run the control wire: You will need to cut into your wiring for the Greasecar electrical system. Locate the wire that you ran from the main fuel selector switch to the 6-port valve. These wires. will default to the diesel fuel sender gauge, in the unlikely event of electrical problems. Now put 2 pieces of electrical tape on this wire close together, and cut the wire in between them.

Strip both ends of the wire that you just cut and insert one side into a butt splice. Crimp on the butt splice on one side. On top of the tank, you will notice both the fuel supply and return lines from the engine.

Get The File: Download here

Owner’s Manual Cadillac Escalade 2002

Content:
Seats and Restraint Systems : Here you’ll find information about the seats in your vehicle and how to use your safety belts properly. You can also learn about some things you should not do with air bags and safety belts. Section 2 Features and Controls Here you can learn about the many standard and optional features on your vehicle, and information on starting, shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is working properly — and what to do if you have a problem.

Section 3 Comfort Controls and Audio Systems : In this section, you’ll find out how to operate the comfort control and audio systems offered with your vehicle. Be sure to read about the particular systems supplied with your vehicle. Comfort Controls, Electronic Climate Control System, Air Conditioning. Defogging and Defrosting, Care of Your Cassette Tape Player. Section 4 Your Driving and the Road : Here you’ll find information about driving on different kinds of roads and in varying weather conditions. We’ve also included many other useful tips on driving. Section 5 Problems on the Road : Here you’ll find what to do about some problems that can occur on the road. Hazard Warning Flashers, Other Warning Devices, If You’re Stuck: In Sand, Mud, Ice or Snow, Section 6 Service and Appearance Care. Here you will find information about the care of your vehicle. This section begins with service and fuel information, and then it shows how to check important fluid and lubricant levels. There is also technical information about your vehicle, and a part devoted to its appearance care. Service, Fuel, Fuels in Foreign Countries, Filling Your Tank, Automatic Transmission Fluid, Electrical System, Normal Maintenance Replacement Parts. Windshield Wiper Blade Replacement.

Opel Calibra Free Repair Manuals

Opel Calibra Service Manual. Opel Calibra (badged as a Vauxhall in the UK, Holden in Australia and New Zealand and Chevrolet in most South American countries, except Chile) is a sports car produced between 1989 and 1997.

Download Free Repair Manuals Opel Calibra
Get the file: Download here

Injector Nozzles Installation Manual for 1997 – 2003 Volkswagen 1.9L TDI.pdf

Remove the engine cover to reveal the engine. 2. Remove the fuel lines using a flat head screwdriveranda17mm wrench. When removing the fuel lines place a paper towel under the line opening stosoakup any fuel leakage. Note that the instructions will refer to the injectors from left right as if facing the engine.

Scheduled Maintenance Guide for 2007 Ford and Lincoln Mercury

Take a few minutes to review this handy Scheduled Maintenance Guide –Make it a habit to use this guide to record scheduled maintenance –Consider your Ford and Lincoln Mercury Dealership for all your vehicle’s needs, Determine which maintenance schedule to follow. It’s important to follow the maintenance schedule that most closely mirrors your driving habits and the conditions under which you drive. For this reason, the Scheduled Maintenance Guide is divided into two basic maintenance schedules.

Oils, Fluids and Flushing In many cases, fluid discoloration is a normal operating characteristic of the chemical compound and may not necessarily demonstrate that a fluid needs to be changed. Oils and Fluids identified in the Owner’s Maintenance Guide should be changed at the specified interval or in conjunction with a repair.

Download Inspection Procedure and Maintenance Schedule for Porsche 968

Earlier variants of Porsche’s 16 valve engines (2.5 liter 944S and 3.0 liter 944S2) used a similar setup but without the Variocam mechanism. Possible Causes of Variocam Failure. Tensioner pads 1 mm (max deepness of tracks in the nylon pads) Camshaft chain 2mm (half stretching of the closed chain, corresponds to 4mm of stretching of an “open” chain). The chain stretching can be measured easily and precisely only by dismounting the old chain (requiring removal of both camshafts) and comparing it with a new one.

Manual Guide – Fuel Pump Control Circuit for 2002 Toyota Tacoma

When the STA signal and NE signal are input to the ECM, Tr is turned on, current flows to the coil of the circuit opening relay, the relay switches on, power is supplied to the fuel pump and the fuel pump operates. While the NE signal is generated (engine running), the ECM keeps Tr on (circuit opening relay on) and the fuel pump also keeps operating. WIRING DIAGRAM DIAGNOSTICS ENGINE (5VZ–FE). INSPECTION PROCEDURE.

System Wiring Diagram Cooling Fan Circuit for 1985 Volvo 240DL/GL

Power Antenna Circuit, Driver’s Heated Seat Circuit, Power Mirror Circuit, Radio Circuits, Power Window Circuit, Charging Circuit, Starting Circuit, Front Washer/Wiper Circuit, Trunk, Tailgate, Fuel Door Circuits, Rear Washer/Wiper W/ Intermittent Relay Circuit, Headlight Washer/Wiper Circuit, Rear Washer/Wiper W/O Intermittent Relay Circuit, Engine Compartment, Fuse Block & Underdash.

Installation Manual TWM Performance Short Shifter 2009 Toyota Corolla

Please Note: It is preferable to park on a flat surface, as you will have to engage and
disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged
to install the short shifter on a slightly inclined surface, place wooden blocks in front and
behind the wheels to prevent the car from moving while you’re working. Please read this
manual completely before beginning to work on your car.
Estimated Installation Time: 60 minutes shifter only, 75 minutes with base bushings
Tools required:
• Flat head screw drivers (small and large)
• Philips head screw driver
• Hammer
• Flash light or shop light **Recommended
• Needle nose pliers
• Rotary cutting tool (Dremel Tool) **Recommended
• Safety glasses
• Shop towels or rags
• Metric socket set (with 10mm, 12mm, and 14mm sockets) and a ratchet with extension
• Punch set (screwdrivers may be substituted)
• Bench Vise
• All purpose automotive grease (white Lithium based grease preferred)

Get the file Download here

Toyota Tacoma Technical Service Bulletin - Front Cowl Water Leak Repair Procedure

Short Description
Use the following field–fix procedure if water is present on the floor carpeting and it can be confirmed that the leak is from the front cowl seam.

Website: www.customtacos.com | Filesize: 55kb
No of Page(s): 4

Content
Toyota Glass Cleaner has been added to Required Tools & Materials. Steps 2 and step 3 have been updated in the confirmation procedures for the front cowl seam leak and the lower front cowl seam leak (step 2: Toyota Glass Cleaner added, step 3: air intake selector should be set to Fresh instead of Recirculate).
…
1. Remove wiper arms and plastic cowl cover. For further removal instructions, refer to the Technical Information System (TIS): 2005 model year Tacoma Repair Manual: Wiper & Washer: Windshield Wiper Motor Assy: Replacement.
2. Locate the left and right front cowl seam and wet area with Toyota Glass Cleaner. Refer to Figure 1 for the location of the left front cowl seam.
…

Get the file Download here

TOYOTA TACOMA FRONT HITCH INSTALLATION

TOYOTA TACOMA

Short Description
1. Remove 2 bolts, one from each end of front bumper beam. Pull out end caps and return to customer.
2. Place 4″ carriage bolt through spacer(CM-SP4) and into existing holes from the inside of the frame (both sides).

Website: sitepro12.sitepro.com | Filesize: 142kb
No of Page(s): 2

Content
3. Where the end cap was removed in step 1, place a 1/2″ x 1 1/4″ carriage bolt through spacer(CM-SP3) into the existing hole in the front bumper beam.
4. Hang side plates from carriage bolts installed in step 2 on the outside of the frames and finger tight with 1/2″ flange nuts.
5. Lift main body into place between side plates and loosely attach using 7/16″ carriage bolts and flange nuts as shown.
6. Attach straps of main body to 1/2″ carriage bolts placed in step 3. Finger tight with 1/2″ flange nuts.
7. Torque all 1/2″ fasteners to 75 ft.-lbs. and 7/16″ fasteners to 50 ft.-lbs. in the following order:
First: Fasten main body to side plates.
Second: Fasten strap to front bumper beam.
Third: Fasten side plates to frame.
…

Get the file Download here

2005 TOYOTA TACOMA REPAIR MANUAL - LIGHTING - LH HEADLAMP ASSY

Short Description
ADJUSTMENT
1. VEHICLE PREPARATION FOR HEADLAMP AIM ADJUSTMENT
(a) Prepare the vehicle:
- Ensure that there is no damage or deformation to the body around the headlamps.
- Fill the fuel tank.
- Make sure that the oil is filled to the specified level.
- Make sure that the coolant is filled to the specified level.
- Inflate the tires to the appropriate pressure.
- Place the spare tire, tools, and jack in their original positions.
- Unload the trunk.
- Sit a person of average weight (68 kg, 150 lb) in the driver’s seat.

Website: www.tundrasolutions.com | Filesize: 52kb
No of Page(s): 5

Content
2. PREPARATION FOR HEADLAMP AIMING (Using a tester)
(a) Prepare the vehicle for headlamp aim check.
(b) Perform adjustment in accordance with the headlamp tester instructions.
3. PREPARATION FOR HEADLAMP AIMING (Using a screen)
(a) Prepare the vehicle according to the following conditions:
- Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlamps can be observed and above which it cannot.
- Place the vehicle at a 90 angle to the wall.
- Keep a 7.62 m (25 ft) distance between the center of the headlamp bulb and the wall.
- Place the vehicle on a level surface.
- Bounce the vehicle up and down to settle the suspension.
…

Get the file Download here

TOYOTA TACOMA - Idle Control System Malfunction

Short Description
The rotary solenoid type IAC valve is located in front of the intake air chamber and intake air bypassing the throttle valve is directed to the IAC valve through a passage. In this way, the intake air volume bypassing the throttle valve is regulated, controlling the engine speed.

Website: www.parksoffroad.com | Filesize: 18kb
No of Page(s): 4

Content
The ECM operates only the IAC valve to perform idle–up and provide feedback for the target idling speed.

INSPECTION PROCEDURE
HINT:
Read freeze frame data using hand–held tester or OBD II scan tool, as freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle was running or stopped, the engine was warmed up or not, the air–fuel ratio was lean or rich, etc. at the time of the malfunction.

PREPARATION:
(a) Warm up the engine to normal operating temperature.
(b) Switch off all the accessories.
(c) Switch off the A/C.
(d) Shift the transmission into the N or neutral position.
(e) Connect the hand–held tester or OBD II scan tool to the DLC3 on the vehicle.
…

Get the file Download here

TOYOTA TACOMA - Evaporative Emission Control System Leak Detected

Short Description
The vapor pressure sensor, VSV for EVAP, VSV for canister closed valve (CCV) and VSV for pressure switching valve are used to detect abnormalities in the evaporative emission control system. The ECM decides whether there is an abnormality in the evaporative emission control system based on the vapor pressure sensor signal.

Website: www.tankota.net | Filesize: 115kb
No of Page(s): 14

Content
DTC P0442 or P0456 is recorded by the ECM when evaporative emissions leak from the components within the dotted line in Fig. 1 below, or when the vapor pressure sensor malfunctions.

After purge operation, the VSV for EVAP is turned off sealing the vacuum in the system and the ECM begins to monitor the pressure increase. It is a normal if the increase in pressure is lower than the predict level. A very rapid, sharp increase in pressure indicates a leak in the EVAP system and sets the DTC P0442. A pressure rise just above normal indicates a very small hole and will set the DTC P0456.
…

Get the file Download here

Toyota - Oil Filter Cap Assembly Precautions

Short Description
The information contained in this TSB supersedes TSB No. T-SB-0332-08.
• Applicability has been updated to include 2009 – 2010 model year Highlander, 2010 model year Camry, Corolla, Matrix, Sequoia, Tundra, and 2009 model year Venza vehicles.
• The SST table has been updated with an illustration.
• The Notice in the Repair Procedure has been updated with a Figure and torque specification ranges to clarify SST usage.
TSB No. T-SB-0332-08 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding.

Website: www.toyotapart.com | Filesize: 208kb
No of Page(s): 4

Content
To prevent damage to the oil filter cap assembly, this procedure must be closely followed during oil filter replacement to avoid immediate and future oil filter serviceability concerns. The following engines are equipped with a plastic oil filter cap assembly:
• 1UR-FE (Tundra, Sequoia)
• 3UR-FE (Tundra, Sequoia, Land Cruiser)
• 2ZR-FE (Corolla, Matrix)
…

Repair Procedure
During oil filter replacement:
• Ensure that SST 09228-06500-02 or 09228-06501 is used to remove and install the oil filter cap — or damage to the cap may occur.
• Inspect the SST for any damage or distortion before use.
• Confirm that the SST is fully seated on the oil filter cap when removing/installing (see Figure 1).
…

Get the file Download here

Toyota Service Bulletin - Shock Absorber Replacement Criteria

Short Description
The purpose of this TSB is to provide a quick reference to assist in making easy judgements regarding shock absorber and strut replacements.

Website: priuschat.com | Filesize: 124kb
No of Page(s): 4

Content
Applicable Vehicles: 2006 – 2007 model year Toyota vehicles.
Condition: Slight oil seepage from oil seal case
Action: Normal oil evaporation — NOT necessary to replace the shock absorber

Condition: Moderate oil seepage from oil seal case
Action: Normal oil evaporation — NOT necessary to replace the shock absorber
…

Get the file Download here

LUBRICATION OIL AND OIL FILTER REPLACEMENT (Toyota 2008 Highlander)

Short Description
CAUTION:
- Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
- Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
- In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.

Website: sumbiz03.home.comcast.net | Filesize: 129kb
No of Page(s): 5

Content
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil drain plug and gasket, and drain the oil into a container.
(c) Clean and install the oil drain plug with a new gasket.
Torque: 40 N·m (408 kgf·cm, 30 ft·lbf)
2. REMOVE OIL FILTER ELEMENT
(a) Remove the oil filter element service hole cover.
(b) Connect a hose with an inside diameter of 15 mm (0.59in.) to the pipe.
(c) Remove the oil filter drain plug from the oil filter cap.
…

Get the file Download here

Toyota - Reset Engine Oil Replacement Reminder Light

Short Description
09 Avalon
After changing the engine oil (U.S.A. only)
The oil change system should be reset. Perform the following procedures:
1. Switch the display to the odometer. (Page 142)
2. Turn the “ENGINE START STOP” switch or the engine switch OFF.
3. Vehicles with smart key system: While pressing the trip meter reset button, turn the “ENGINE START STOP’ switch to IGNITION ON mode. Continue to press and hold the button until the trip meter displays 000000.
Vehicles without smart key system: While pressing the trip meter reset button, turn the engine switch to the “ON” position. Continue to press and hold the button until the trip meter displays 000000.

Website: www.beavertontoyota.com | Filesize: 95kb
No of Page(s): 6

Content
‘09 Camry
Changing the engine oil (U.S.A. only)
To reset the oil change system, follow the procedure below:
1. Turn the “ENGINE START STOP” switch or engine switch OFF with the trip meter A reading shown. (Page 149)
2. While pressing the trip meter reset button (page 141), turn the “ENGINE START STOP’ switch or engine switch ON.
- Without multi-information display
3. Continue to press and hold the knob until the trip meter displays 000000.
- With multi-information display
3. Continue to press and hold the knob until “COMPLETE” appears on the multi-information display.
…

Get the file Download here

Kawasaki ZZR 1400, ZZR1400 ABS, Ninja ZX-14 Service Manual

Section :
Fuel System (DFI), Cooling System, Engine Top End, Clutch, Engine Lubrication System, Engine Removal & Installation, Crankshaft/Transmission, Wheels & Tires,
Final Drive, Brakes, Suspension, Steering, Frame.

Get the file Download Here

Maintenance and Service Manual Guide for 2004 Toyota Rampvan

Troubleshooting Diagnosis Chart, Below Floor Obstructions, Wiring Diagrams and Electrical Schematics Pre-2007 Power Door, Infloor Rampvan and Kneel Wiring Diagram. Kneel Electrical Schematic, Kneel Wiring Diagram, Electrical Schematic, Repair Parts Infloor Ramp Assembly Parts List Infloor Ramp Assembly Exploded View.

Troubleshooting : 1.11 Poor ground connection 1.12 Battery terminals dirty 1.13 Battery damaged 1.14 Battery discharged 1.15 12 volt source (check fuses for 12 volts) 1.16 Circuit breaker tripped or damaged.

2005-2008 Toyota Tacoma Exhaust System Installation

Short Description
Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance Exhaust System on your vehicle will eliminate the restrictive design of the stock exhaust, allowing your engine to discharge exhaust gas easier. The result is more horsepower and torque, longer engine life, and a distinctive throaty growl- all this, with easy bolt-on installation. These installation instructions have been written to help you in the installation of your Borla Performance Exhaust System. Please read it completely before installing your system.

Website: www.borla.com | Filesize: 1611kb
No of Page(s): 4

Content
Thank you for purchasing a Borla Performance Cat-Back? Exhaust System. Borla Performance Cat-Back? Exhaust System (Part number 140140) has been designed for 2005-2008 Toyota Tacoma Double Cab, long bed equipped with a 4.0L V-6 engine and automatic or manual transmissions. Borla Performance Cat-Back Exhaust System (Part number 140160) has been designed for 2005-2008 Toyota Tacoma Double Cab, short bed and Extended Cab, long bed equipped with a 4.0L V-6 engine and automatic or manual transmissions. Borla Performance Cat-Back? Exhaust System (Part number 140269) has been designed for 2005-2008 Toyota Tacoma X-runner Extended Cab, short bed equipped with a 4.0L V-6 engine 2 & 4 wheel drive and automatic or manual transmissions.
…

Get the file Download here

TOYOTA SHIFT INTERLOCK SYSTEM

Short Description
The shift lock system is designed to ensure the proper operation of the automatic transmission. The driver must depress the brake pedal in order to move the gear selector from Park to any other range. In addition, the ignition key cannot be turned to the Lock position and removed from the ignition switch unless the gear selector is placed in the Park position.

Website: www.autoshop101.com | Filesize: 240kb
No of Page(s): 8

Content
There are three systems available in Toyota models; electrical, electrical/ mechanical and mechanical. We will not cover the application by model but rather by system type. For the specifics on a particular model, consult the repair manual.

Electrical Shift Lock Type
The electrical type uses electrical control of the shift lock mechanism, as well as the key lock mechanism.

Shift Lock Mechanism
The shift lock mechanism is made up of a number of components as seen in the illustration below.

The shift position switch (shift lock control switch) is used to detect the position of the shift lever. It has two contacts, P1 and P2. When the select lever is in the Park position, P1 is on (closed) and P2 is off (open). In this position, the key can be removed but the select lever is locked in position. When the select lever is in a position other than Park, P1 is off (open) and P2 is on (closed). In this position, the key cannot be removed.
…

Get the file Download here

Excerpts From 1990 Toyota Celica Repair Manual

Short Description
This manual contains maintenance and repair procedures for the 1990 CELICA. Applicable modles: AT180 series, ST184 series. The manual is divided into 21 sections and 4 appendixes with a thumb index for each section at the edge of the pages.

Website: www.ntsb.gov | Filesize: 377kb
No of Page(s): 9

Content
…
Inspection of Front Brake Components
1. Measure Pad Lining thickness. Standard thickness: 10.0mm (0.39 in.). Minimum thickness: 1.0mm (0.039 in.). Replace the pad if the thickness is less than the minimum of if its shows sign of uneven wear.
2. Measure rotor disc thickness. Standard thickness: 22.0mm (0.866 in.). Minimum thickness: 20.0mm (0.787 in.). If the disc is scored or worn, of if thickness is less than minimum, repair or replace the disc.
…

Get the file Download here

TOYOTA TUNDRA 2007- BIG BRAKE KIT Installation

Short Description
If the OE wheels are not used, then see the brake caliper template available from your dealer via Toyota’s TIS system or TRD.com. The brake caliper template must be used to insure there is adequate clearance between new brake components and non-OE wheels and balancing weights.

Website: www.tundraheadquarters.com | Filesize: 548kb
No of Page(s): 10

Content
…
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:-
- Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
- Safety (eye protection, rechecking torque procedure, etc.).
- Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
- Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
…

Get the file Download here

Toyota Technical Service - BRAKE ACTUATOR NOISE 04-07 Prius

Short Description
Some 2004–2007 model year Prius vehicles may exhibit a squeak–type noise when pressing or releasing the brake pedal. This noise may only be audible when the vehicle is in “READY” mode and the vehicle is not moving. Brake system performance is not affected by this noise. Use the following procedure to address this concern.

Website: priuschat.com | Filesize: 35kb
No of Page(s): 2

Content
…
1. Confirm noise condition by pressing/releasing the brake pedal.
2. Bleed the brake system.
Refer to the Technical Information System (TIS):
- 2004 or 2005 model year Prius Repair Manual, Brake – Brake System – “Brake Fluid: Bleeding”.
- 2006 or 2007 model year Prius Repair Manual, Brake – System – “Brake: Brake Fluid: Bleeding”.
If the noise is NO longer present when pressing/releasing the brake pedal, the repair is complete.
If the noise is still present, go to step 3.
3. If the noise is still present, replace the Brake Actuator Assembly.
Refer to TIS:
- 2004 or 2005 model year Prius Repair Manual, Brake – Brake Control/Dynamic Control System – “Brake Actuator ASSY: Replacement”.
- 2006 or 2007 model year Prius Repair Manual, Brake – Brake Control/Dynamic Control System – “Brake Control: Brake Actuator: Replacement
…

Get the file Download here

The Peugeot 206 Range

Short Description
The information and images in this brochure are based on the current technical data when going to print. The equipment shown is factory fitted or available as an option at extra cost, depending on the model. Where a feature is described as an option it should be assumed that it is at extra cost unless specifically stated otherwise.As part of a policy of continuous specification improvement, Peugeot reserve the right to modify the technical equipment, options and colours at any time.

Website: www.donnellygroup.co.uk | Filesize: 361kb
No of Page(s): 7

Content
206 CC
“My mood may change quicker than the weather, but I still hate to compromise.”
You find freedom enticing, luxury seductive. But you wouldn’t sacrifice one for the other.
Happily, you can keep all your options open with the sensational 206 CC.
The 206 CC is two distinctive cars in one. It’s a luxurious coupé with more than enough room to relax in, then at the touch of a button the rigid steel roof vanishes and it’s a heart-wrenchingly beautiful cabriolet that leaves nothing between you and the sky.
But whichever way you look at it, with its low, sporty profile, high bootline and sleek alloys, plus a choice of engines that now includes a smooth, responsive HDi 110 diesel, the 206 CC is in a class of its own.
The interior welcomes you with comfortable reclining front seats and aluminium pedals*, and spoils you with air-conditioning**. Not to mention a radio / CD player. Then your foot goes down, and your pulse starts to rise… it feels like nothing could dampen your enthusiasm. Not even the weather.
…

Get the file Download here

NEW INDEX TO CATALOG CURENTLY UNDER RENOVATION

MARANELLO CONCESSIONAIRES FERRARI GUIDE TO FERRARI PRODUCTION 1959 TO 1978 WITH PHOTOS ETC. FERRARI FNA ORIGINAL CHRISTMAS CARDS FROM THE 1970'S. …

Website: www.who-sells-it.com | Filesize: 342kb

Content
Page 1
To place an order, email us at NUNZIO@FERRARILITERATURE.COM or fax us - 908-362-5878
EMAIL YOUR ORDER OR QUESTIONS TO
NUNZIO@FERRARILITERATURE.COM
UPDATED MONTHLY * VISIT THE WEB SITE OFTEN !
WE ACCEPT VISA, MASTERCARD, , AMERICAN EXPRESS / CHECKS
*****WE BUY FERRARI CARS..WHEN IT IS TIME TO SELL, CALL/FAX US WITH
YOUR DETAILS******
WE ALSO CARRY THE FOLLOWING AUTOMOBILE MANUFACTURERS
PLEASE CHECK THE THIS CATALOG FOR :
ALFA ROMEO ARBARTH ALLARD AMERICAN MOTORS
ASTONMARTIN ASA AVANTI BENTLEY BIZZARRINI BUGATTI
BRADLEY BITTER CHECKER CISITALIA CADILLAC CORVETTE
CHRYSLER DELOREAN DE TOMASO PANTERA DODGE DUESENBERG
EXCALIBAR FIAT FORD FIBERFAB GRAHAM SUPERCHARGER
HONDA INTERMECCANICA ISO JENSEN HEALEY LAMBORGHINI
LANCIA LOTUS MASERATI MARCOS MORGAN MG MERCURY
MONTEVERDI MVS PANTERA PONTIAC PORSCHE TVR
VOLKSWAGEN
AND THE FOLLOWING OTHER RELATED MANUFACTURERS
AGOSTINI KARTS ASPREY AUTOLITE BORG AND BECK CERRUTI
CHAMPION CHAPELLE DUNLOP GOODYEAR HARLEY DAVIDSON
KONI JOHN LOBB MAGNETI MARELLI MOMO PININFARINA
PIRELLI SCAGLIETTI SCANDIA SCHWINN TOD’S TUBI
ULYSSE NARDIN VANDERVELL KURT WHITE
NEW INDEX TO CATALOG
CURENTLY UNDER RENOVATION
AUCTION CATALOGS…

Get the file Download here

JBL AND CENTRAL SIGHT &amp SOUND JUICE UP CUSTOMIZED HUMMER H2

technology and equipment, a customized Hummer H2 is the impressive creation of. Central Sight & Sound, featuring the highest quality in audio equipment from …

Website: manuals.harman.com | Filesize: 94kb

Content
Media Contact:
Katie Wittenburg
DeLyon-Hunt & Associates
310-374-6893
katie@delyon-hunt.com
FOR IMMEDIATE RELEASE
(with images)
JBL?AND CENTRAL SIGHT & SOUND JUICE UP
CUSTOMIZED HUMMER?H2
Central Sight & Sound’s latest store opening showcases JBL?installation
Woodbury, NY (October, 2006) - It’s hard to overlook a Hummer?H2 cruising down
the street, so imagine the celebrity-style punch it packs with the latest JBL audio
equipment installed in the powerhouse vehicle. Enhanced with cutting-edge audio
technology and equipment, a customized Hummer H2 is the impressive creation of
Central Sight & Sound, featuring the highest quality in audio equipment from JBL.
Known as one of the leading custom mobile electronics specialists in the industry,
Central Sight & Sound researched several H2 installs prior to completing this project, to
ensure that it would surpass anything ever done before. Although JBL typically provides
the standard 12- or 15-inch subwoofers for H2 installs, in this case the same amount of
robust output was achieved stylishly and compactly with 8-inch subwoofers.
“JBL prides itself on our unique relationship with our dealers,” commented Christopher
M. Dragon, director of brand marketing, Harman…

Get the file Download here

Ferrari Service Guide Annual 6000 Miles Major 18000 Miles Cam Belt …

Ferrari Service Guide … Maserati Service Guide … All servicing will be carried out to factory service schedules by Paul, our Ferrari factory …

Website: www.paulwitts.com | Filesize: 87kb

Content
Ferrari Service Guide
Annual
6,000
Miles
Major
18,000
Miles
Cam Belt
Only
Cam Belt &
Major
18,000
Miles
Valve
Clearances
Clutches
from
308 & 328 ?440 ?780 ?340 ?1,000 ?400 POA
348 &
Mondial
?540 ?835 ?770 ?1,360 ?400 POA
F355 ?540 ?835 ?770 ?1,360 POA
360 ?685 ?980 ?370 ?1,270 POA
400 & 412 ?785 ?1,780 ?400 POA
456 ?785 ?1,280 ?770 ?1,860 ?600 POA
550 & 575 ?785 ?1,280 ?770 ?1,860 POA
Testarossa
512TR/M
?470 ?1,080 ?770 ?1,360 ?400 POA
F40 ?460 ?850 ?450 ?1200 ?400 POA
F50 ?750 ?1,350 ?400 POA
Maserati Service Guide
3200 ?685 ?980 ?370 ?1,270 POA
4200 ?685 ?980 POA
All servicing will be carried out to factory service schedules by Paul, our Ferrari factory
trained technician with Ferrari/Maserati genuine parts.
The above is but a small amount of the work we are trained and equipped to carry out. In
order for…

Get the file Download here

Bologna Konferenz 2007

The First 4 Stroke Ducati Motorcycle Engine … Left: Motorcycle jumps too short; Right: Head-first impact leads to hyperflexion …

Website: www.fh-zwickau.de | Filesize: 7375kb

Content
4thInternational Conference HAUS DER TECHNIK e.V.FTZ-Research and Technology Association at the West Saxon University of ZwickauVenueDUCATIMOTOR HOLDING S.p.A.AuditoriumVia Cavalieri Ducati, 340132, BolognaItaly10.-11. May 2007ChairmanProf. Dr.-Ing. habil. Prof. E.h Dr. h. c. Cornel Stan,FTZ -Research and Technology Associationat the West Saxon University of ZwickauBOLOGNA 2007…

Get the file Download here

2006 MEDIA GUIDE SCUDERIA ECOSSE RACING WITH FERRARI MEDIA GUIDE …

Short Description
2006 MEDIA GUIDE. Last Update: 20 March 2006. SCUDERIA ECOSSE: RACING WITH FERRARI. Scuderia Ecosse races Ferrari GT cars in both national and international …

Website: www.scuderiaecosse.com | Filesize: 719kb

Content
Media Enquiries:
Lindsay Morle
lindsay@morle.com
+44 (0) 7971 481078
Commercial Enquiries:
Lynn Rankin
commercial@
scuderiaecosse.com
+44 (0) 1506 890724
www.scuderiaecosse.com
2006 MEDIA GUIDE
Last Update: 20 March 2006
SCUDERIA ECOSSE: RACING WITH FERRARI
Scuderia Ecosse races Ferrari GT cars in both national and international motorsport events. The team took a dominant victory in the 2005 British GT Championship with Nathan Kinch and Andrew Kirkaldy in a Ferrari 360 GTC; and also took victory in the LMES race at Istanbul Park. In 2006 the team will run a pair of Ferrari 430s in the FIA GT Championship, alongside an assault on the British GT Championship. The 430 is an exciting new prospect from Maranello and Scuderia Ecosse will also be competing for victory at the world-famous Le Mans 24 Hours, the team’s ultimate ambition. Operating with the full endorsement of Ferrari and Michelotto in Italy, and led by owner, Stewart Roden, Scuderia Ecosse operates from impressive facilities on the outskirts of Edinburgh, Scotland.
MEDIA GUIDE CONTENTS
(a) 2006 Racing Schedules
(b) Driver biography - Nathan Kinch
(c) Driver biography - Andrew Kirkaldy
(d) Driver biography - Chris…

Get the file Download here

OFFICIAL RESULTS Novice Driver &quotStage by Stage&quot

Daihatsu Charade G102. 0:04:16. 0:04:16. 0:00:26. 0:00:05. 7. 25. Alexandra Kirkhouse … Daihatsu Charade G102. 0:10:58. 0:10:58. 0:01:13. 0:00:31 …

Website: www.lightcarclub.com.au | Filesize: 302kb

Content

Get the file Download here

Dodge Expands Commercial Presence, Charges into Class 4-5 Segment …

More Than 2.4 Million Test Kilometres Logged by Dodge Truck Engineers. Commercial customers expect to put their trucks to work and get exceptional …

Website: www.dodge.ca | Filesize: 156kb

Content
February 7, 2007
Dodge Expands Commercial Presence, Charges into Class 4-5
Segment with All-new 2008 Ram 4500 and 5500 Chassis Cabs
All-new chassis cabs showcase dominant commercial capability, durability and
dependability
?Legendary Cummins Turbo Diesel in 6.7-litre displacement with 610 lb.-ft. of torque
?Best-in-class First-gear ratio provides optimum acceleration on vehicle take-off
?Largest standard fuel tank in segment and largest front brakes in segment
?Flat, clean frame rails with industry-standard 860-millimetre frame rail spacing — all
chassis components below top of frame surface
Chicago — Extending bold, tough, in-your-face Dodge Ram heritage to the Class 4 and 5
commercial market, Dodge expands its commercial presence and sets another commercial
standard with the launch of the all-new 2008 Dodge Ram 4500 and 5500 Chassis Cabs.
“We built the all-new 2008 Dodge Ram 4500 and 5500 Chassis Cabs for heavy-duty chassis
cab buyers who want a powerful, capable and versatile commercial-quality vehicle,” said
George Murphy, Senior Vice President - Global Brand Marketing, Chrysler Group. “With
commercial performance, durability and capability, the 2008 Dodge Ram 4500 and 5500
Chassis Cabs…

Get the file Download here

The 39 Tokyo Motor Show Officially Opens

The “Daihatsu Charade”. (E-G10) was the world’s first 4-cycle, 3-cylinder, 1000-cc. engine vehicle and created a new genre that came to be known …

Website: www.tokyo-motorshow.com | Filesize: 4754kb

Content
Chairman Koeda of the
Japan Automobile Manufacturers
Association greets the
audrence
The opening ceremony started at 10:30 a.m. Approximately
900 dignitaries and industry representatives were in attendance;
a screen behind the podium showed snapshots and clips looking
back over the 50 years of the Tokyo Motor Show. The
ceremony began with a greeting from Chairman Itaru Koeda
representing the Japan Automobile Manufacturers Association.
“It has been 50 years since the first Tokyo Motor Show was
held in Hibiya Park in 1954. This show marks the start of a new
half-century,” he said and went on to describe the second
milestone set this year. “This show also marks the last Passenger
Cars and Motorcycles show. Beginning in 2007 (the next
show), the Tokyo Motor Show will be reorganized as a general
show that will include commercial vehicles and commercial
vehicle bodies.” Following this, the Chairman briefly described
the show theme and exhibits before explaining that Tokyo had
become “the longest motor show in the world” because the
organizers wanted to include three weekends to alleviate
congestion. Throughout the 17 days, the show will be holding a
variety of events, from a retrospective of classic…

Get the file Download here

DAIHATSU CHARADE 5 DAIHATSU CHARADE 5 DAIHATSU CHARADE 5 DAIHATSU …

DAIHATSU CHARADE 5 SPEED SYNCHROMESH KI. SPEED SYNCHROMESH KI. SPEED SYNCHROMESH KI. SPEED SYNCHROMESH KIT. Albins close ratio gear sets are designed to …

Website: www.albinsgear.com.au | Filesize: 306kb

Content
24 Wi l t sh i r e L ane , De lac ombe 3356 Ba l l ar at Vic t or i a Aus t r al i a
t e l e p h te lephone: +61 3 5335 8022 f ac s imi le : +61 3 5335 8366
web : www.a l b in s . c om. au emai l : a dmi n@a l b in s . c om. au
ALBINS OFF ROAD GEAR
?Over 25 years of exper ience in suppl y ing qual i t y products to al l forms of motor racing.
?Al l des igns are car r ied out in house us ing the latest 3D des ign technology .
?Latest state of the ar t CNC machiner y ensures qual i t y of par ts.
?Qual i t y as sured company - ISO 9001:2000
?We source wor ldwide to guarantee the highest grade and cleanest raw mater ial avai lable.
?Al l steel used for shaf ts and gears is cer t i f ied and independent l y tested to ensure…

Get the file Download here